Vacuum Freeze Drying Pilot Plant Vacuum Freeze Dryer,Vacuum Freeze Dried Machine,Vacuum Freeze Dried Equipment,Vacuum Freeze Drying Pilot Plant Dalian Iceberg Freeze-dry Technology Co.,Ltd , https://www.freezedrydliceberg.com
When the user gets the basket-type tablet press, how to scientifically install and debug it? The whole machine is installed. The whole machine can be connected to the top by wire rope, or it can be transported by forklift. The machine should be leveled before the machine is in place. Power cord installation: Cable specifications are compatible with motor power, voltage and current. The cable is connected through the main switch via a wire tube or socket plug with a flexible cable; the cable enters the electrical box through the exit coil behind the base.
Under normal circumstances, the steering of the motor should be consistent with the indication sign (ie, it should be counterclockwise from the outer end of the pulley on the motor). The triangle belt should be removed before the proofreading, and the V-belt should be installed after the proofreading. The button confirms the correctness of the steering.
When installed, cut off the power supply, wipe the die holes of the middle die plate, the upper and lower punch holes and the die, and install them. After the installation is completed, adjust the filling depth. Experts suggest: “Unscrew the set screws on both sides of the filling adjustment nut. When the nut is lowered, the filling depth can be increased. After adjustment, the screw must be tightened and tightened. Note that the filling depth should not exceed 45 mm.â€
The thickness of the tablet and the adjustment of the film were then carried out. When adjusting the output, turn the pulley (shun) to raise the lower punch to the highest position, loosen the screws on both sides of the adjustment nut, and rotate the output adjustment nut so that the lower punch upper end faces the middle die end. Qi, after adjustment, tighten the screws on both sides. In addition, the operator has to adjust the position of the feeder and the lower punch.
The basket-type tablet press can be operated after installation, but it should be reminded that there are also many things to be aware of when operating the equipment. Before use, check whether the die has quality problems such as missing edge, crack, deformation, etc. Check whether the machine is in good condition; to check whether the granular particles meet the requirements, the fine powder content in the granule should not exceed 10%, so as not to affect the performance of the equipment. And life.
In addition, before the operation, apply the hand to rotate the pulley or click the button to test the pressure to ensure that the tablet meets the requirements. After the machine is running normally, it can be put into production. The machine is equipped with a reversing jog button, which can be used when the sheet is produced by lamination or the punching and squeezing of the car.
When using, only the momentary jog is allowed to make the machine slightly reverse, otherwise the machine will be damaged. Also pay attention to the operation of the machine at all times during use. If there is abnormal noise, it should be stopped for inspection and then used after troubleshooting.
There are also manufacturers of flower basket presses. When connecting the power supply, pay attention to the running direction of the machine. Do not reverse it to avoid damage to the machine. When debugging the machine, the power should be cut off to avoid injury. The reverse transfer button can only be used when rushing into the mold on the pressure relief or debugging observation, and can not be used at will, so as not to cause damage to the machine.
The protective cover and safety cover on the machine should be installed before use and cannot be removed. The die should have no quality problems such as cracks, deformation, and missing edges. Do not use the non-conforming product to avoid damage to the machine and affect the quality of the tablet. To adjust the mechanism or troubleshoot, it must be stopped to avoid personal injury. In addition, do not allow the oil to spill out when refueling, so as not to affect the quality of the tablets.
Basket-type tablet press makes tablet production more convenient
The basket type tablet press is a one-way tablet based on manual stamping, that is, a machine that presses the sheet under the punching and does not move, and only presses the punching motion, and then presses the granular material into a tablet through the pressing wheel, Automatically adjust pressure, control chip weight, remove waste, print data, display downtime and other functions. In addition to being able to control the difference in sheet weight within a certain range, the basket type tablet press can automatically identify and eliminate quality problems such as missing corners and loose pieces.