The STL water-jacketed Gold Concentrator is a kind of gravity separation equipment. It was developed by Changchun Gold Research Institute Co., Ltd. in 1985 and entered the market. At present, it has been used in many domestic and foreign companies. It is suitable for the recovery of single gold in placer gold, vein gold mines and polymetallic mines, instead of mercury plate operations. The addition of large single gold particles in the collected ore before flotation can further increase the recovery rate of gold mines, and it can also be used from gold-bearing mines. Separate single gold from flotation gold-copper concentrate and flotation gold concentrate.
The main indicators of this series of equipment basically reach the level of similar international products (such as Nielsen gold selectors, etc.). Compared with similar equipment at home and abroad, this series of equipment has the advantages of high cost performance, easy operation, and low maintenance costs.
Gold Separation System,Fluid Bed Gold Concentrator,Gold Rough Separating Machine,Gold Centrifugal Concentrator Changchun Gold Research Institute Co.LTD , https://www.ccgrizbs.com
Technical Parameters:
â—† External power supply: 220V AC or 24V DC
â—† Input
Signal: Receive a signal from a VS Series Vibration Speed ​​Sensor
Sensitivity: 20mV/mm/s±5%
Frequency response: 5 ~ 300Hz
◆ Range: 0 ~ 500μm (peak - peak) or 0 ~ 50.0mm / s (true RMS)
â—† LED indication: OK green, Alert, Danger red.
◆ Measurement error: ±1% of full scale
◆ Current output: 4~20mA active, output load ≤500Ω
◆ Alarm point setting: 0~100% full scale, accuracy ±1%
â—† Alarm reset mode: automatic or manual (site reset button, remote alarm reset terminal)
â—† Relay seal: epoxy resin, node capacity DC30V/5A or 220V/5A, single pole double throw
â—† Power-on delay: about 10 seconds
◆ Temperature range: -25°C～+65°C during operation, -40°C～+85°C during storage
â—† Relative humidity: up to 95%, no condensation
ZH1251-A60-B01 vibration (intensity) (speed) transmitter â—† external power supply: 220V AC or 11, TR203124V DC
â—† Input
Signal: Receive a signal from a VS Series Vibration Speed ​​Sensor
Sensitivity: 20mV/mm/s±5%
Frequency response: 5 ~ 300Hz
◆ Range: 0 ~ 500μm (peak - peak) or 0 ~ 50.0mm / s (true RMS)
â—† LED indication: OK green, Alert, Danger red.
◆ Measurement error: ±1% of full scale
◆ Current output: 4~20mA active, output load ≤500Ω
◆ Alarm point setting: 0~100% full scale, accuracy ±1%
â—† Alarm reset mode: automatic or manual (site reset button, remote alarm reset terminal)
â—† Relay seal: epoxy resin, node capacity DC30V/5A or 220V/5A, single pole double throw
â—† Power-on delay: about 10 seconds
◆ Temperature range: -25°C～+65°C during operation, -40°C～+85°C during storage
◆ Relative humidity: up to 95%, non-condensing Measurement range: Amplitude: 0 ~ 500μm (peak-to-peak);
Intensity: 0 ~ 50.0mm / s (true RMS);
- Frequency range: 5 to 3000 Hz;
- Measurement accuracy: 0.5, linear error ≤ ± 0.5%;
- Output signal: current output: 4 ~ 20mA, load resistance ≤ 850Ω;
- Use environment: -40 ° C ~ 65 ° C, relative humidity ≤ 95% (non-condensing);
- Power supply voltage: DC24V power consumption ≤ 1W;
When evaluating the operating state of a rotating machine, the relative axis vibration is the authoritative of all the signs of failure related to the condition of the machine. This is because it directly reflects the rapid radial movement of the rotor shaft relative to the bearing housing. It is a basic indicator. Many mechanical failures such as rotor imbalance, misalignment, bearing wear, shaft cracks, etc. can be detected.
Fault monitoring
Monitor the radial vibration of the rotating machine rotor, measure the shaft vibration, swing, eccentricity, etc., and monitor the vibration increase caused by the imbalance of the rotor, misalignment, loose parts.
ZH1251-A60-B01 vibration (intensity) (speed) transmitter
ZH1251-A60-B01 vibration (intensity) (speed) transmitter