This standard specifies the working capacity, responsibility, authority and operating procedures of the belt conveyor. 2. area This standard applies to the operator of the belt machine and its inspection and assessment. 3 job ability requirements 3.1 Those who have passed the training of this post and passed the third-level safety education. 3.2 Have a junior high school education or above. 3.3 Familiar with the working principle of the equipment operated by this post and its safe operation procedures. 4 Responsibility 4.1 Responsible for its own safety. 4.2 Responsible for the safety supervision of non-employees who enter this position. 4.3 Responsible for the safe operation of electromechanical equipment in this position. 4.4 Responsible for the fastening, lubrication and maintenance of the equipment. 4.5 Responsible for the entire process of transport. 4.6 Responsible for the cleaning of this position. 5 permissions 5.1 The right to prevent non-employee staff from entering the work area. 5.2 The right to prevent employees who are not wearing protective products from entering the work area. 5.3 Have the right to prevent illegal command and illegal operation. 6 indicator requirements 6.1 Roller rotation rate: 100%. 6.2 Belt speed: 1# belt 2.5 2# belt 2.5 3# belt 2.5 4# belt 2.5 5# belt 3.15 6# belt 2.5 7# belt 2.5 8# belt 2.5 9# belt 1.0 7.1 Â Â Dangerous source of this position 7.1.1 Potential ore flying out of the workshop area. 7.1.2 The position of the dust is too large or the operator is negligent in wearing a dust mask. 7.1.3 The post noise is too large or the operator is negligent in wearing anti-noise earplugs. 7.1.4 There are more potential slips on the post stairs. 7.1.5 The operator does not operate according to the operating procedures, such as not carefully checking before driving, the operator going to work after drinking or not paying attention, during the belt running, the hand reaches into the lower wheel of the belt or the belt. 7.1.6 During the operation of the belt, when the belt is deflected, the belt is not operated according to the operating procedures, and the hand or other parts of the body are involved. 7.2 Safety precautions and control measures 7.2.1, carefully observe the surrounding environment, beware of the ore flying out 7.2.2 Take precautions against dust hazards and wear dust masks during work. 7.2.3 Take precautions against noise hazards and wear anti-noise earplugs during work. 7.2.4 Regularly check the integrity of the protective railings and their stairways, and beware of falling down and falling from high places. 7.2.5 Attention and careful inspection of the integrity of the rollers, rollers and deviation devices at all times. 7.2.6 Strengthen business learning, put an end to unsafe behaviors, and operate in strict accordance with the operating procedures. 7.2.7 Attention and careful inspection of the power line, the motor is connected to zero, the grounding wire and its protective cover are in good condition. 7.2.8 Wear labor protection articles in strict accordance with the requirements, and wear helmets as standard. 7.2.9 Regularly inspect the entire belt to see if any ore is stuck, causing the belt to be damaged or torn. 7.3 Environmental factors of this post 7.3.1 Noise generated by the operation of the equipment. 7.3.2 Dust and raw lime dust formed during the production process. 7.3.3 Oil leakage from the equipment. 7.3.4 Leakage and leakage of powder during belt operation. 7.3.5 Pipes, valves leaking water, standing water. 7.3.6 Waste materials are not cleaned and concentrated. 7.3.7 Equipment and environmental sanitation are not cleaned. 7.4 Environmental Considerations and Control Measures 7.4.1 Take precautions against dust hazards and wear dust masks during work. 7.4.2 Take precautions against noise hazards and wear anti-noise earplugs during work. 7.4.3 Strengthen the maintenance and maintenance of the equipment, deal with oil spills and clean up the contaminated site in time. 7.4.4 Clean up the leakage and leakage of powder in time, and do a good job in prevention and treatment. 7.4.5 Dispose of leaks of pipes and valves in time, and clean up water in the post. 7.4.6 Clean up the waste materials in time and classify them in a centralized manner. 7.4.7 Clean equipment and environmental sanitation in a timely manner. 8.5 Operating procedures 8.5.1 Before driving, carefully check the strength, lubrication and wear of the transmission parts and rollers. Whether the cleaning device is in good condition, whether the electrical equipment and protective facilities are intact, whether the belt is damaged or strained, whether the funnel baffle or the lining plate is damaged, and the oil quantity and oil quality of the reducer and the hydraulic coupler. 8.5.2 It is strictly forbidden to touch the running part by hand after starting. It is forbidden to move the protective cover and it is strictly prohibited to cross the belt. 8.5.3 Check the operation of the equipment, be responsible for timely cleaning the non-crushed objects on the belt conveyor, and adjust the belt deviation in time. 8.5.4 Check the feeding and dropping funnels to prevent blockage and check the running condition of the rollers and rollers, such as heat and abnormal sound. Crusher off preventing member and the funnel above the iron belt is torn belt falls. 8.5.5 promptly clean up the debris and metal separator metal detector to detect the absorption. 8.5.6 The belt should start at no load. Parking can be stopped after the materials to be transported are stopped after parking. 8.5.7 Do the following equipment lubrication work Aluminum Alloy Come Along Clamp
Aluminum alloy Come Along Clamp is mainly made of LC4 high-strength aluminum alloy die forging, with light weight. It has the advantages of high strength and no damage to the surface of conductor by clamping conductor. The aluminum alloy wire grip is made of high strength aluminum alloy forging die, light weight and high strength. The conductor surface will not be damaged when the conductor is clamped.
The aluminum alloy come along clamp is mainly composed of movable jaw base, connecting plate, pull ring, fixed jaw (lower jaw), movable jaw (upper jaw), body and other components. Strengthening the hook can improve the overall stress condition of the come along clamp and make it more safe and reliable.
After the come along clamp holds the ground wire, the tension is applied to the pull ring, and the sliding shaft of the pull ring slides in the body wire slot, and drives the connecting plate, and the movable jaw seat rotates accordingly. Because the other end of the movable jaw seat is hinged firmly with the jaw, when rotating, the movable jaw is forced to press down along the pin shaft, and the cable is pressed on the fixed jaw seat. The greater the tension on the pull ring, the greater the downward pressure on the movable jaw, so as to ensure that the ground wire is tightly clamped by the movable jaw and the fixed jaw.
Aluminum Alloy Come Along Clamp, Aluminum Alloy Wire Grip, Conductor Clamp, Conductor Grip Taizhou Haoxin Electric Power Machine Co., Ltd. , https://www.hxstringingequipments.com
Broken ore belt work standard
1 Subject content